MODEL 54 TRANSITION ADAPTER (FT x GR)
Shurjoint standard fitting pressure ratings conform to the ratings of Model 7707 couplings.
Cotización
Cotización
MODEL 7110 90o ELBOW, REGULAR RADIUS
Shurjoint grooved-end elbows are made of ductile iron per ASTM A536 Gr. 65-45-12 and or ASTM A395 Gr. 65-45-15. C-E dimensions are manufacturer’s standard.
Cotización
MODEL 7111 45o ELBOW, REGULAR RADIUS
Shurjoint grooved-end elbows are made of ductile iron per ASTM A536 Gr. 65-45-12 and or ASTM A395 Gr. 65-45-15. C-E dimensions are manufacturer’s standard.
Shurjoint standard fitting pressure ratings conform to the ratings of Model 7707 couplings.
MODEL 7112 22½o ELBOW
Shurjoint grooved-end elbows are made of ductile iron per ASTM A536 Gr. 65-45-12 and or ASTM A395 Gr. 65-45-15. C-E dimensions are manufacturer’s standard.
Shurjoint standard fitting pressure ratings conform to the ratings of Model 7707 couplings.
Cotización
Cotización
MODEL 7113 11¼o ELBOW
Shurjoint grooved-end elbows are made of ductile iron per ASTM A536 Gr. 65-45-12 and or ASTM A395 Gr. 65-45-15. C-E dimensions are manufacturer’s standard.
Shurjoint standard fitting pressure ratings conform to the ratings of Model 7707 couplings.
Cotización
Cotización
MODELS 7120 TEE
Shurjoint grooved-end fittings are made of ductile iron per ASTM A536 Gr. 65-45-12 and or ASTM A395 Gr. 65-45-15. C-E dimensions are manufacturer’s standard.
Shurjoint standard fitting pressure ratings conform to the ratings of Model 7707 couplings.
Cotización
Shurjoint standard fitting pressure ratings conform to the ratings of Model 7707 couplings.
Cotización
MODELS 7135 CROSS
Shurjoint grooved-end fittings are made of ductile iron per ASTM A536 Gr. 65-45-12 and or ASTM A395 Gr. 65-45-15. C-E dimensions are manufacturer’s standard.
Shurjoint standard fitting pressure ratings conform to the ratings of Model 7707 couplings.
Cotización
Shurjoint standard fitting pressure ratings conform to the ratings of Model 7707 couplings.
Cotización
MODELS 7130 45o LATERAL
Shurjoint grooved-end fittings are made of ductile iron per ASTM A536 Gr. 65-45-12 and or ASTM A395 Gr. 65-45-15. C-E dimensions are manufacturer’s standard.
Shurjoint standard fitting pressure ratings conform to the ratings of Model 7707 couplings.
Cotización
Cotización
MODEL 7121 REDUCING TEE
Shurjoint grooved-end reducing tees are made of ductile iron per ASTM A536 Gr. 65-45-12 and or ASTM A395 Gr. 65-45-15. C-E dimensions are manufacturer's standard.
For sizes larger than 14” (350 mm) are fabricated from standard weight (0.375” or 9.5 mm) carbon steel pipe to ASTM A234 GR. WPB or segmentally welded with carbon steel of the same or equivalent grade. C-E & C-B dimensions conform to ANSI B16.9.
Shurjoint standard fitting pressure ratings conform to the ratings of Model 7707 couplings.
Cotización
Cotización
MODELS 7150 CONCENTRIC REDUCER
Shurjoint grooved-end reducers are made of ductile iron per ASTM A536 Gr. 65-45-12 and or ASTM A395 Gr. 65-45-15. C-E dimensions are manufacturer's standard.
For sizes larger than 14” (350 mm) are fabricated from standard weight (0.375” or 9.5 mm) carbon steel pipe to ASTM A234 GR. WPB or segmentally welded with carbon steel of the same or equivalent grade. E-E dimensions conform to ANSI B16.9.
Shurjoint standard fitting pressure ratings conform to the ratings of Model 7707 couplings.
Cotización
Cotización
MODELS 7151 ECCENTRIC REDUCER
Shurjoint grooved-end reducers are made of ductile iron per ASTM A536 Gr. 65-45-12 and or ASTM A395 Gr. 65-45-15. C-E dimensions are manufacturer's standard.
For sizes larger than 14” (350 mm) are fabricated from standard weight (0.375” or 9.5 mm) carbon steel pipe to ASTM A234 GR. WPB or segmentally welded with carbon steel of the same or equivalent grade. E-E dimensions conform to ANSI B16.9.
Shurjoint standard fitting pressure ratings conform to the ratings of Model 7707 couplings.
Cotización
Cotización
MODEL 7160 END CAP
Shurjoint grooved-end fittings are made of ductile iron per ASTM A536 Gr. 65-45-12 and or ASTM A395 Gr. 65-45-15. C-E dimensions are manufacturer’s standard.
Shurjoint standard fitting pressure ratings conform to the ratings of Model 7707 couplings.
Cotización
Cotización
MODEL 7160P END CAP WITH PLUG
Shurjoint grooved-end fittings are made of ductile iron per ASTM A536 Gr. 65-45-12 and or ASTM A395 Gr. 65-45-15. C-E dimensions are manufacturer’s standard.
Shurjoint standard fitting pressure ratings conform to the ratings of Model 7707 couplings.
Cotización
Cotización
MODEL 7160T TRANSITION FITTING (Gr x Ft)
The Model 7160T grooved x threaded transition fitting can be the ideal fitting when transitioning from a larger grooved pipe to a smaller threaded pipe such as 6" x 1", 4" x 1" etc. The 7160T can be used as an alternative to expensive swaged nipples.
Shurjoint standard fitting pressure ratings conform to the ratings of Model 7707 couplings.
Cotización
Cotización
MODEL 7160H DOMED END CAP
Shurjoint 7160H end caps are cast of ductile iron and are designed to withstand pressure evenly over the entire spherical surface. The Model 7160H End Cap is designed for use on 10” ~ 24” mechanical piping applications.
Cotización
Cotización
MODEL 7110LR 1.5D LONG RADIUS 90o ELBOW
Shurjoint grooved-end fittings are made of ductile iron per ASTM A536 Gr. 65-45-12 and or ASTM A395 Gr. 65-45-15. C-E dimensions are manufacturer’s standard.
Shurjoint standard fitting pressure ratings conform to the ratings of Model 7707 couplings.
Cotización
Cotización
MODEL 7111LR 1.5D LONG RADIUS 45o ELBOW
Shurjoint grooved-end fittings are made of ductile iron per ASTM A536 Gr. 65-45-12 and or ASTM A395 Gr. 65-45-15. C-E dimensions are manufacturer’s standard.
Shurjoint standard fitting pressure ratings conform to the ratings of Model 7707 couplings.
Cotización
Cotización
MODEL 7137 TRUE-Y
Shurjoint grooved-end fittings are made of ductile iron per ASTM A536 Gr. 65-45-12 and or ASTM A395 Gr. 65-45-15. C-E dimensions are manufacturer’s standard.
Shurjoint standard fitting pressure ratings conform to the ratings of Model 7707 couplings.
MODEL 7112G 22½o ELBOW, Goose Neck Design
Two model 7112G elbows in combination with a coupling will serve as a universal joint and is ideal for instances where a pipe line is in need of a slight adjustment during make-up.
Cotización
Cotización
MODEL 7110-B 90o ELBOW, REGULAR RADIUS With Base Support
Model 7110-B is a ductile iron 90o grooved-end elbow with base support, designed for installation at the bottom of a riser system. An anchor can be placed in conjunction with the base support to support the weight of the pipe, coupling and fluid.
Shurjoint standard fitting pressure ratings conform to the ratings of Model 7707 couplings.
MODEL 901 SHORT RADIUS 90o ELBOW
Shurjoint short radius fittings, while primarily designed for fire protection applications, can also be used for general service requirements. The Model K-9 and Z05 rigid couplings can be used with short radius fittings without the worry of bolt pad interference.
Shurjoint grooved-end fittings are made of ductile iron per ASTM A536 Gr. 65-45-12 and or ASTM A395 Gr. 65-45-15. C-E dimensions are manufacturer’s standard.
Shurjoint standard fitting pressure ratings conform to the ratings of Model 7707 couplings.
MODEL 903 SHORT RADIUS TEE
Shurjoint short radius fittings, while primarily designed for fire protection applications, can also be used for general service requirements. The Model K-9 and Z05 rigid couplings can be used with short radius fittings without the worry of bolt pad interference.
Shurjoint grooved-end fittings are made of ductile iron per ASTM A536 Gr. 65-45-12 and or ASTM A395 Gr. 65-45-15. C-E dimensions are manufacturer’s standard.
Shurjoint standard fitting pressure ratings conform to the ratings of Model 7707 couplings.
MODEL 7110DR DRAIN ELBOW
Shurjoint grooved-end fittings are made of ductile iron per ASTM A536 Gr. 65-45-12 and or ASTM A395 Gr. 65-45-15. C-E dimensions are manufacturer’s standard.
Shurjoint standard fitting pressure ratings conform to the ratings of Model 7707 couplings.
The Model 7110DR is a grooved-end ductile iron cast elbow with an integral 1” NPT or BSP drain. The 7110DR was primarily designed for, but not limited to, use on fire protection standpipes.
MODEL 7127 STANDPIPE TEE
Shurjoint grooved-end fittings are made of ductile iron per ASTM A536 Gr. 65-45-12 and or ASTM A395 Gr. 65-45-15. C-E dimensions are manufacturer’s standard.
Shurjoint standard fitting pressure ratings conform to the ratings of Model 7707 couplings.
The Model 7127 is a grooved-end tee with a 2½” NPT/BSP threaded branch, specially designed for use on fire protection standpipes.
MODEL 7125 BULLHEAD TEE
Shurjoint grooved-end fittings are made of ductile iron per ASTM A536 Gr. 65-45-12 and or ASTM A395 Gr. 65-45-15. C-E dimensions are manufacturer’s standard.
Shurjoint standard fitting pressure ratings conform to the ratings of Model 7707 couplings.
The Model 7125 is a grooved-end bullhead tee, specially designed for use on fire protection systems. The 7725 allows you to directly split the flow into two reduced branch lines without the need for concentric reducers and multiple couplings.
MODEL 7150F REDUCING SOCKET ADAPTER (Gr x Ft)
Shurjoint ductile iron grooved-end fittings are made of ductile iron per ASTM A536 Gr. 65-45-12 and or ASTM A395 Gr. 65-45- 15. C-E dimensions are manufacturer’s standard.
Shurjoint standard fitting pressure ratings conform to the ratings of Model 7707 couplings.
The Shurjoint Models 7150F & 7150M are designed for making direct reduction from a grooved system to female or male threaded system without the need for expensive swaged nipples.
MODEL 7150M REDUCING NIPPLE (Gr x Mt)
Shurjoint ductile iron grooved-end fittings are made of ductile iron per ASTM A536 Gr. 65-45-12 and or ASTM A395 Gr. 65-45- 15. C-E dimensions are manufacturer’s standard.
Shurjoint standard fitting pressure ratings conform to the ratings of Model 7707 couplings.
The Shurjoint Models 7150F & 7150M are designed for making direct reduction from a grooved system to female or male threaded system without the need for expensive swaged nipples.
MODEL 899 END-ALL FITTING
The Model 899 End-All fitting is a unique domed end cap fitting available with a ½”, ¾” or 1” NPT or BSP threaded outlet. Designed as an end of line fitting, the End-All features two multi-function bosses which can be used for the direct connection of sprinkler heads, sprigs, drops, drains and or gauges. The Model 899 End-All fitting pressure ratings conform to the ratings of the coupling used to join the system.
MODEL 55 NIPPLE ADAPTER (Gr x Mt)
Shurjoint ductile iron grooved-end fittings are made of ductile iron per ASTM A536 Gr. 65-45-12 and or ASTM A395 Gr. 65-45- 15. C-E dimensions are manufacturer’s standard.
Shurjoint standard fitting pressure ratings conform to the ratings of Model 7707 couplings.
The Shurjoint Model 55 is a cast adapter that allows for a direct transition from grooved system to a male threaded system. For other sizes, see our Model #59 pipe nipples.
MODEL 56 HOSE NIPPLE
The Shurjoint Model 56 hose nipple allows for a direct connection with rubber or plastic hoses.
Shurjoint standard fitting pressure ratings conform to the ratings of Model 7707 couplings.
SPRINKLER HUBS
MODELS 850, 851 & 853
The Shurjoint Sprinkler Hubs are grooved-end manifold fittings with a number of threaded outlets to accommodate flexible sprinkler hoses. The Sprinkler Hubs can also be used in combination with flexible sprinkler hoses and traditional hard piping depending on your requirements. These fittings work as a hub for multiple flexible hoses and or hard pipe runs, thus reducing the number or headers, drop nipples and fittings required. All outlets are 1” NPT or BSPT. Maximum working pressure 300 psi (20 bar, 2.0 MPa) CWP. cULus listed and FM approved. The C-to-E dimensions conform to ANSI B16.3 Class 150.
SPRINKLER HUBS
MODELS 850, 851 & 853
The Shurjoint Sprinkler Hubs are grooved-end manifold fittings with a number of threaded outlets to accommodate flexible sprinkler hoses. The Sprinkler Hubs can also be used in combination with flexible sprinkler hoses and traditional hard piping depending on your requirements. These fittings work as a hub for multiple flexible hoses and or hard pipe runs, thus reducing the number or headers, drop nipples and fittings required. All outlets are 1” NPT or BSPT. Maximum working pressure 300 psi (20 bar, 2.0 MPa) CWP. cULus listed and FM approved. The C-to-E dimensions conform to ANSI B16.3 Class 150.
MODEL 7114 HYDRANT ELBOW
The Model 7114 Hydrant Elbow is designed for use on fire protection systems. The small end of the elbow is 2½" BSP threaded and also grooved to 3" pipe size. The boss can be factory tapped to 1" BSP on request.
MODEL 7122 HYDRANT TEE
The Model 7122 Hydrant Tee is designed for use on fire protection systems. The 7122 is supplied with a 2½" BSP threaded and 3” grooved outlet. The boss can be factory tapped to 1” BSP on request.
MODEL 7133 PITCHER TEE
The Shurjoint pitcher tee provides a quick and easy connection and transition from a grooved riser system to a screwed and flanged hydrant valve outlet. The pitcher tee is designed for 3”, 4” or 6” (88.9 mm, 114.3 mm or 165.1 mm O.D.) steel pipe risers with a 2½” BSP taper threaded or 3” grooved hydrant connection outlet.
- Easy installation with two grooved couplings.
- Easy positioning of the outlet direction.
- Reduces total installed cost.
- LPCB approved.
Shurjoint Model 7133 pressure ratings conform to the working pressure of the coupling used to join the system.
Edcos Equipos y Materiales Contra Incendio
Calle Norte 35, No. 895-D
Col. Industrial Vallejo, México, D.F. 02300
(55) 8526 3082
info@equiposymaterialescontraincendio.com
Edcos, Inc. USA
330 Industrial Park
Mercedes,Texas 78570, USA
(956) 565-5660 (70)
(956) 513-0469
sales@edcos.com
No hay comentarios:
Publicar un comentario